Installing Netspark with Uninstall Protection on iPhone/iPad

Installing Netspark with Uninstall Protection on iPhone/iPad



  1. If the device you intend to install Netspark on has Stolen Device protection turned on, it is recommended to install in a trusted place (home, work, etc.), otherwise you will need to wait until the one hour Security Delay ends. For more details please click here 

  2. Installing Netspark with Uninstall protection requires a computer. 
    If you wish only to install the filter, check out this guide.
  3. If you already have Netspark installed and wish to prevent removing it, check out this guide. 
  4. To see the guide in Hebrew click here מדריך בעברית


Installing with a Windows PC

Download the Installation file to you PC 
Open the file, connect the iPhone/iPad with a USB cable to the PC and make sure you trust the computer when the notification appears on the device

  1. Click Start on the Welcome screen

  2. Backup the content of your device:

    Open iTunes→    Right click the device from the list→select the Backup button
    Make sure you have the iTunes program installed from the official Apple website (not Microsoft store). If its not installed you can find it here.
  3. Once backup is done, click Next

  4. Disable your Passcode:
        Open Settings  -->Tap Face ID & Passcode  or Touch ID & Passcode  -->Enter your existing Passcode -->Turn Passcode Off. 

  5. Once Passcode is disabled click Next

  6. Disable Find My iPhone:
       Open Settings →Tap your Apple ID→Tap Find My →Tap Find My iPhone→Toggle to turn it off.

  7. Once Find My iPhone is disabled click Next

  8. The Installtion process will now take place.
    Make sure you do not disconnect or switch off the device

  9. When prompted, enter the License Activation Code and click Next

  10. The installation process will continue and your device will be restarted

  11. Once the device restarts, click Next on the configuration screen,


  12. Click Finish on the Installation process screen

  13. The process will finalize some configurations 

  14. Your device in now filtered and protected, and Netspark app can only be removed using a password from the Admin panel


Note:
You may now re-enable the device's Passcode and Find my iPhone.


Installing with a Mac

Step 1 - Download and run the Uninstall Protection setup file

  1.  Download the Installation setup file.
    The file named Netspark_iOS_Protection.dmg with the Netspark icon will appear in your computer's Downloads folder.
  2. Double click the Netspark icon.
  3. Connect The iPhone/iPad to the mac with a USB cable, Trust the computer if asked, then click Start on the setup guide screen.  

    Step 2 - Backup your device using Finder

  1. Open Finder   on your Mac.
  2. Select your device in the Finder sidebar.
  3. Click Back Up Now (below Backups).

  4. Click Next on the installation setup screen on your Mac.


Step 3 - Disable your Passcode

  1. Open Settings  on your iOS device.
  2. Tap Face ID & Passcode  or Touch ID & Passcode 
  3. Enter your existing Passcode.
  4. Turn Passcode Off.
  5. Click Next on the installation setup screen on your Mac
    screenshot passcode
  6. Go back to Settings on your iOS device.
  7. Tap your Apple ID name.
  8. Tap Find My 
  9. Tap Find My iPhone, then tap again to turn it off.
     
  10. Enter your Apple ID password, then tap Turn Off.
  11. Click Next on the installation setup screen on your Mac

    Step 4 - Activation code
  1. When prompted, enter your Activation code

  2. Allow the installation to process without removing the device 

Step 5 - Enable Remote Management
  1. After the device restarts, tap Continue

  2. Tap Apply configuration
  3. Tap Next
  4. Wait until the device's Home Screen loads, then click the Finish button on your Mac. 
    Important! Do not click Finish until the Home Screen loads